GT-30-1 90 Degree Peel Test Fixture

Perform quick and accurate 90-degree peel tests with our test fixtures.

Models Available

GT-30-1-LF – For testing from 0-44 lbf
GT-30-1 – For testing from 10-44 lbf

*NOTE GT-30-1 includes slide bearing table and string bolt only.
Other grips pictured are sold separately.

P45-50N 45 Degree Peel Tester

P45-50N 45 Degree Peel Tester can measure the peak value of the beginning of the opening cover.

Peeling strength of a film cover of the plastic container. For food and medical care etc.

For more details, please contact us for Pricing and Availability..!!

 

G1109 90° Peel Test Fixture

The G1109 peel test fixture is designed for peel testing of tapes, films, foil seals, and other materials. A large, flat working table moves horizontally as the test stand’s crosshead moves up via direct cable linkage.
An optional adjustable-angle mount tilts the fixture up to ±30°.
Another optional adapter uses an adjustable pulley to set the angle of pull, from 0° to 90°, while the working table remains horizontal.
The horizontal orientation is suited for seal testing of filled containers, and can also be used for tapes and other materials.
An integrated limit switch automatically stops the motion of an ESM303 motorized test stand when the working table has reached its end of travel.

*Test Stand and Force Gauge is sold separately.

For more details, please contact us for Pricing and Availability..!!

ESM303-003 Safety Shield For ESM303 Test Stand

The ESM303-003 safety shield attaches to an ESM303 test stand, providing pinch and sample debris protection for the operator.
The shield is constructed of rugged PETG material.
It rotates via ultra-smooth bearings in both the clockwise and counter-clockwise directions, guided into the open or closed positions with magnetic detents.
An electrical interlock prevents test stand operation while the door is open.
For crosshead adjustment during sample loading, the FollowMe™ force-based positioning function is active even while the door is open.
The FollowMe™ function is included with the shield and does not need to be separately ordered with the test stand.

Compatibility Note:

FollowMeTM may be used in all new ESM303 test stands and existing ESM303 test stands with the following minimum firmware versions:

Front: 2.02.08
Main: 2.02.07

With earlier firmware versions, the door interlock is still operational, however, FollowMeTM cannot be activated while the door is open. Test stand firmware upgrades are available at no charge. Contact Mark-10 for details.

MH-500 Motorized Horizontal Test Stand

The MH-500 motorized test stand offers consistent and reliable testing.
Our Basic or Auto Cycle models are available in Standard, High, and Low speeds.
Speed control, quick return, and emergency stop are standard features.
They accept any of the standard range Imada force gauges and special attachments.
Optional digital distance meter is also available.

Basic Model: MH-500BA
Basic Models have top and bottom travel limits that can be adjusted for a precise range of movement. Set the travel limits, flip the direction switch up to move the crosshead up to the top travel limit at the selected speed. Flip the direction switch down to send the crosshead down to the bottom travel limit. The speed is set by a Speed Adjust knob. Quick Return and Emergency Stop features are also included.

Auto Cycle Model: MH-500AC
Autocycle models have top and bottom travel limits that can be adjusted for a precise range of movement. Speed Adjust, Quick Return, and Emergency Stop features are also included. These stands have three function modes.

Manual Mode:
While the Direction switch is held up, the head moves up. Holding the switch down moves the crosshead down. When the switch is released the head stops. This mode is ideal for positioning.

Single Cycle Mode:
When the Direction switch is pushed up, the crosshead moves up at the desired speed, and when it reaches the top travel limit, it automatically goes back and stops at the bottom travel limit, completing one cycle. Pushing the switch down runs the cycle in reverse.

Auto Cycle Mode:
This mode is similar to Single Cycle mode, except that the crosshead travels up and down repeating the cycle until either the Power or Emergency switches is turned off. This mode is ideal for applications such as fatigue testing.

Models Available
MH-500-BA
MH-500-BA Motorized Horizontal Test Stand, Basic Model
MH-500-AC
MH-500-AC Motorized Horizontal Test Stand, Auto Cycle

TSTM-DC Motorized Torque Test Stand

The TSTM-DC Advanced Motorized Torque Test Stand offers all the mechanical specifications of the TSTM motorized test stand, including standard 100 lbFin (11.5 Nm) torque capacity, versatile modular design, quick engagement and disengagement of samples, fixture mounting plate, stepper motor design that prevents speed variation with load, and more. A 200 lbFin (22 Nm) capacity upgrade is available as an option.

The TSTM-DC offers expanded capabilities, including full PC control, programmable angle limits, programmable cycling, auto return, password protection, and other features.

Models Available

TSTM-DC
Motorized Torque Test Stand – Vertical with digital speed controller – Vertical
TSTMH-DC
Motorized Torque Test Stand – Vertical with digital speed controller – Horizontal
EU-PLUG
Euro type plug supplied in place of USA type plug

For more details, please contact us for Pricing and Availability..!!

MX-1100 Motorized Vertical Test Stand

MX-1100 motorized test stands offer advanced force testing. The combination of the screw system and the state-of-the-art brushless motor provides extremely smooth and powerful operation over the entire speed range.

Connect the MX-1100 test stand with a Z Series force gauge and enable force controlled testing. Force control can automatically stop testing when the force value reaches the high setpoint programmed on the Z Series force gauge, or maintain the force between the Z Series High and Low setpoints.
Force control is ideal for fatigue or non-destructive testing.

High/Low Set Point Force Control
Force control is activated when the applied force is at or between the high and low setpoint(s) of the force gauge and is deactivated by the digital timer. Initial carriage speed is controlled by the variable or fixed speed settings.

One Way Force Control
Initial carriage speed is controlled by the variable or fixed speed settings. When the applied force reaches the low set point of the force gauge, the test stand’s carriage speed is adjusted to 20% of maximum and decreases to zero as the applied force reaches the high set point. Ideal for non-destructive testing.

Speed control, The MX-1100 accepts any of the standard range force gauges.
A quick switch and Emergency Stop features are also included.

Models Available

MX-1100
MX-1100 Motorized Test Stand
MX-1100-S
MX-1100 Motorized Test Stand with distance meter

*FORCE GAUGE NOT INCLUDED
Designed to work with the Z2 & ZP force gauges.

For more details, please contact us for Pricing and Availability..!!

MH-275 Motorized Horizontal Test Stand

The new MH-275 motorized test stand is designed for tension, compression, and friction testing. A combination of a screw system and the state-of-the-art brushless motor provides extremely smooth and powerful operation over the entire speed range. Speed control, quick return, and emergency stop are standard features.

The MH-275 accepts the DPS, Z2 & ZP force gauges, additional models require the AP-002 adapter plate.

High/Low Setpoint Force Control
When the force value reaches the Low setpoint, force control is activated to hold the tension or compression force between the High and Low setpoints programmed on the Imada Z Series force gauge. Use the optional digital timer to program the duration of the hold, up to 100 minutes in 1second increments. Ideal for non-destructive testing.

High Setpoint Force Control
When the force value reaches the Low setpoint, speed is reduced to the test speed set by the Speed Adjust Knob, and when the tension or compression force value reaches the High setpoint programmed on the Imada Z Series force gauge, the test stops. Ideal for creep testing.

Speed control, quick return, and emergency stop are standard features. The MH-275 accepts any of the standard range Imada force gauges.
Optional timer and digital distance meter available.

Models Available

MH-275 – With Auto Cycle & Force Control
MH-275-S – With Auto Cycle, Force Control & Distance Meter

*FORCE GAUGE NOT INCLUDED
Designed to work with the DPS, Z2 & ZP force gauges.

For more details, please contact us for Pricing and Availability..!!

MX-275 Motorized Vertical Test Stand

The new MX-275 motorized test stands offer advanced force testing. The combination of a screw drive system and the state-of-the-art brushless motor provides extremely smooth and powerful operation over the entire speed range.
Connect the MX-275 test stand with a Z2 or ZP Series force gauge and enable force controlled testing.

High/Low Set Point Force Control
Force control is activated when the applied force is at or between the high and low setpoint(s) of the Z Series force gauge and is deactivated by the digital timer. Initial carriage speed is controlled by the variable or fixed speed settings.

One Way Force Control
Initial carriage speed is controlled by the variable or fixed speed settings. When the applied force reaches the low set point of the Z Series force gauge, the test stand’s carriage speed is adjusted to 20% of maximum and decreases to zero as the applied force reaches the high set point. Ideal for non-destructive testing.

Speed control, quick switch, and emergency stop are standard features.
Optional timer and digital distance meter available.

Models Available

MX-275
MX-275 Motorized Vertical Test Stand
MX-275S
MX-275S Motorized Vertical Test Stand with Distance Meter

*FORCE GAUGE NOT INCLUDED
Designed to work with the Z2 & ZP force gauges.

For more details, please contact us for Pricing and Availability..!!

TSFM500-DC Motorized Test Stand

The TSFM500-DC is an Advanced Motorized Force Measurement Test Stand with a capacity of 500 lbF [2,200 N]. The stand offers generous clearance and throat depth, rugged construction, stepper motor design that prevents speed variation with load, and more.
Additional features include PC control, programmable cycling, auto return, and other features.

Models Available

TSFM500-DC
Motorized Test Stand, 500 lb Capacity, Vertical
TSFM500H-DC
Motorized Test Stand, 500 lb Capacity, Horizontal

For more details, please contact us for Pricing and Availability..!!