ESM303-003 Safety Shield For ESM303 Test Stand

The ESM303-003 safety shield attaches to an ESM303 test stand, providing pinch and sample debris protection for the operator.
The shield is constructed of rugged PETG material.
It rotates via ultra-smooth bearings in both the clockwise and counter-clockwise directions, guided into the open or closed positions with magnetic detents.
An electrical interlock prevents test stand operation while the door is open.
For crosshead adjustment during sample loading, the FollowMe™ force-based positioning function is active even while the door is open.
The FollowMe™ function is included with the shield and does not need to be separately ordered with the test stand.

Compatibility Note:

FollowMeTM may be used in all new ESM303 test stands and existing ESM303 test stands with the following minimum firmware versions:

Front: 2.02.08
Main: 2.02.07

With earlier firmware versions, the door interlock is still operational, however, FollowMeTM cannot be activated while the door is open. Test stand firmware upgrades are available at no charge. Contact Mark-10 for details.

MH-500 Motorized Horizontal Test Stand

The MH-500 motorized test stand offers consistent and reliable testing.
Our Basic or Auto Cycle models are available in Standard, High, and Low speeds.
Speed control, quick return, and emergency stop are standard features.
They accept any of the standard range Imada force gauges and special attachments.
Optional digital distance meter is also available.

Basic Model: MH-500BA
Basic Models have top and bottom travel limits that can be adjusted for a precise range of movement. Set the travel limits, flip the direction switch up to move the crosshead up to the top travel limit at the selected speed. Flip the direction switch down to send the crosshead down to the bottom travel limit. The speed is set by a Speed Adjust knob. Quick Return and Emergency Stop features are also included.

Auto Cycle Model: MH-500AC
Autocycle models have top and bottom travel limits that can be adjusted for a precise range of movement. Speed Adjust, Quick Return, and Emergency Stop features are also included. These stands have three function modes.

Manual Mode:
While the Direction switch is held up, the head moves up. Holding the switch down moves the crosshead down. When the switch is released the head stops. This mode is ideal for positioning.

Single Cycle Mode:
When the Direction switch is pushed up, the crosshead moves up at the desired speed, and when it reaches the top travel limit, it automatically goes back and stops at the bottom travel limit, completing one cycle. Pushing the switch down runs the cycle in reverse.

Auto Cycle Mode:
This mode is similar to Single Cycle mode, except that the crosshead travels up and down repeating the cycle until either the Power or Emergency switches is turned off. This mode is ideal for applications such as fatigue testing.

Models Available
MH-500-BA
MH-500-BA Motorized Horizontal Test Stand, Basic Model
MH-500-AC
MH-500-AC Motorized Horizontal Test Stand, Auto Cycle

TSTM-DC Motorized Torque Test Stand

The TSTM-DC Advanced Motorized Torque Test Stand offers all the mechanical specifications of the TSTM motorized test stand, including standard 100 lbFin (11.5 Nm) torque capacity, versatile modular design, quick engagement and disengagement of samples, fixture mounting plate, stepper motor design that prevents speed variation with load, and more. A 200 lbFin (22 Nm) capacity upgrade is available as an option.

The TSTM-DC offers expanded capabilities, including full PC control, programmable angle limits, programmable cycling, auto return, password protection, and other features.

Models Available

TSTM-DC
Motorized Torque Test Stand – Vertical with digital speed controller – Vertical
TSTMH-DC
Motorized Torque Test Stand – Vertical with digital speed controller – Horizontal
EU-PLUG
Euro type plug supplied in place of USA type plug

For more details, please contact us for Pricing and Availability..!!

MX-1100 Motorized Vertical Test Stand

MX-1100 motorized test stands offer advanced force testing. The combination of the screw system and the state-of-the-art brushless motor provides extremely smooth and powerful operation over the entire speed range.

Connect the MX-1100 test stand with a Z Series force gauge and enable force controlled testing. Force control can automatically stop testing when the force value reaches the high setpoint programmed on the Z Series force gauge, or maintain the force between the Z Series High and Low setpoints.
Force control is ideal for fatigue or non-destructive testing.

High/Low Set Point Force Control
Force control is activated when the applied force is at or between the high and low setpoint(s) of the force gauge and is deactivated by the digital timer. Initial carriage speed is controlled by the variable or fixed speed settings.

One Way Force Control
Initial carriage speed is controlled by the variable or fixed speed settings. When the applied force reaches the low set point of the force gauge, the test stand’s carriage speed is adjusted to 20% of maximum and decreases to zero as the applied force reaches the high set point. Ideal for non-destructive testing.

Speed control, The MX-1100 accepts any of the standard range force gauges.
A quick switch and Emergency Stop features are also included.

Models Available

MX-1100
MX-1100 Motorized Test Stand
MX-1100-S
MX-1100 Motorized Test Stand with distance meter

*FORCE GAUGE NOT INCLUDED
Designed to work with the Z2 & ZP force gauges.

For more details, please contact us for Pricing and Availability..!!

MH-275 Motorized Horizontal Test Stand

The new MH-275 motorized test stand is designed for tension, compression, and friction testing. A combination of a screw system and the state-of-the-art brushless motor provides extremely smooth and powerful operation over the entire speed range. Speed control, quick return, and emergency stop are standard features.

The MH-275 accepts the DPS, Z2 & ZP force gauges, additional models require the AP-002 adapter plate.

High/Low Setpoint Force Control
When the force value reaches the Low setpoint, force control is activated to hold the tension or compression force between the High and Low setpoints programmed on the Imada Z Series force gauge. Use the optional digital timer to program the duration of the hold, up to 100 minutes in 1second increments. Ideal for non-destructive testing.

High Setpoint Force Control
When the force value reaches the Low setpoint, speed is reduced to the test speed set by the Speed Adjust Knob, and when the tension or compression force value reaches the High setpoint programmed on the Imada Z Series force gauge, the test stops. Ideal for creep testing.

Speed control, quick return, and emergency stop are standard features. The MH-275 accepts any of the standard range Imada force gauges.
Optional timer and digital distance meter available.

Models Available

MH-275 – With Auto Cycle & Force Control
MH-275-S – With Auto Cycle, Force Control & Distance Meter

*FORCE GAUGE NOT INCLUDED
Designed to work with the DPS, Z2 & ZP force gauges.

For more details, please contact us for Pricing and Availability..!!

MX-275 Motorized Vertical Test Stand

The new MX-275 motorized test stands offer advanced force testing. The combination of a screw drive system and the state-of-the-art brushless motor provides extremely smooth and powerful operation over the entire speed range.
Connect the MX-275 test stand with a Z2 or ZP Series force gauge and enable force controlled testing.

High/Low Set Point Force Control
Force control is activated when the applied force is at or between the high and low setpoint(s) of the Z Series force gauge and is deactivated by the digital timer. Initial carriage speed is controlled by the variable or fixed speed settings.

One Way Force Control
Initial carriage speed is controlled by the variable or fixed speed settings. When the applied force reaches the low set point of the Z Series force gauge, the test stand’s carriage speed is adjusted to 20% of maximum and decreases to zero as the applied force reaches the high set point. Ideal for non-destructive testing.

Speed control, quick switch, and emergency stop are standard features.
Optional timer and digital distance meter available.

Models Available

MX-275
MX-275 Motorized Vertical Test Stand
MX-275S
MX-275S Motorized Vertical Test Stand with Distance Meter

*FORCE GAUGE NOT INCLUDED
Designed to work with the Z2 & ZP force gauges.

For more details, please contact us for Pricing and Availability..!!

TSFM500-DC Motorized Test Stand

The TSFM500-DC is an Advanced Motorized Force Measurement Test Stand with a capacity of 500 lbF [2,200 N]. The stand offers generous clearance and throat depth, rugged construction, stepper motor design that prevents speed variation with load, and more.
Additional features include PC control, programmable cycling, auto return, and other features.

Models Available

TSFM500-DC
Motorized Test Stand, 500 lb Capacity, Vertical
TSFM500H-DC
Motorized Test Stand, 500 lb Capacity, Horizontal

For more details, please contact us for Pricing and Availability..!!

FGS-220VC Motorized Force Test Stand

The FGS-VC Series Motorized Force Test Stands are designed to provide accurate and repeatable results for tension, compression, break and cycle performance tests in various applications.
A key feature is an FGS-VC exclusive: a precision-made servo gear head and ball screw for precise movement control. The large measurement area plus tall 15.75″ (400 mm) travel distance allows large, unique parts to be tested.
A precise and consistent 0.40-15.75″/min (10-400mm/min) adjustable speed provides for slow tests or quick cycle load testing.
The simple keypad combined with the intuitive on-screen operation guides the user through setting up each test. Users can perform standard tests in several automatic or manually selected modes as well as choose higher-end capabilities with the additional dwell time, adjustable acceleration, plus user-defined tests with up to 5 programmed set points.
The FGS-VC’s are flexible as they can be operated by the keypad or through a PC via the FGT-VC software which includes data collection, graphing, and statistical analysis.
The FGT-VC software program allows graphing of force versus distance and the ability to compare several tests on a single graph. Another great feature of the FGT-VC is the comparator mode which enables quick decision pass /fail determination, ideal for production line testing.
The FGS-VC’s can be equipped with various gripping and compression fixtures and are compatible with all of our Force Gauges as well as most gauges on the market. These features make the new FGS-VC the ideal push/pull tester for the production line or QC lab.

For more details, please contact us for Pricing and Availability..!!

MX-110 Motorized Vertical Test Stand

The new MX-110 test stand offers consistent and reliable testing. The combination of a screw drive system and the state-of-the-art brushless motor provides extremely smooth and powerful operation over the entire speed range.
Connect The MX-110 test stand with a Z Series force gauge and enable force controlled testing.
Force control can automatically stop testing when the force value reaches the high setpoint programmed on the Z Series force gauge, or maintain the force between the Z Series High and Low setpoints.
Force control is ideal for fatigue or non-destructive testing.
The MX-110 accepts any of the standard range force gauges.
A quick switch and Emergency Stop features are also included.

Capacities Available

MX-110
Motorized Test Stand, Capacity: 110 lb / 50 Kg / 500N, Speed: 0.4 – 11.5 in/min
MX-110-F
Motorized Test Stand, Capacity: 80 lb / 36 Kg / 360N, Speed: 0.8 – 23.0 in/min
MX-110-WF
Motorized Test Stand, Capacity: 40 lb / 18 Kg / 180N, Speed: 1.6 – 47.0 in/min
MX-110S
MX-110S Motorized Test Stand w/Distance Meter
MX-110S-HS
MX-110S-HS Motorized Test Stand w/Distance Meter

*FORCE GAUGE NOT INCLUDED
Designed to work with the Z2 & ZP force gauges.

For more details, please contact us for Pricing and Availability..!!

FGS-100E Motorized Force Test Stand

The Series FGS-100E Vertical, Motorized Force Test Stands combined with our superior quality force gauges, create a complete force measurement system capable of handling the most precise testing applications.
The test stand’s all-steel construction makes them remarkably rugged while performing with precision, providing the reliability to tackle a multitude of applications.
The FGS-100E’s possess simplified operation with their 7 button key-pad and emergency stop button, eliminating lengthy training typical of similar test stands.
With four modes of operation (manual, jog, single cycle, continuous) various single tests or repetitive tests can be achieved and selected with the push of a button.

Capacities Available

FGS-100E-L
Vertical Motorized Test Stand with low speed 0.23-7.00 in/min (6-180 mm/min) and 110 lb (50 kg) capacity
FGS-100E-H
Vertical Motorized Test Stand with high speed 0.78-23.60 in/min (20-600 mm/min) and 110 lb (50 kg) capacity

For more details, please contact us for Pricing and Availability..!!