PZX-7 DL Series

Range with Standard Delay Line Transducer
0.0060″ – 1.000″ / 0.150 – 25.40 mm

Range with Contact Transducers
up to 36.00″ / 915.0 mm

The PZX-7 DL series gauges are basic single element precision gauges and equipped with a variety of measurement modes to address a number of potential applications.

They can use both high and low-frequency transducers with a variety of diameter options. Both models have USB-C connectivity, with and without data storage, and serial over USB-C using a CDC class.

Applications
Precision Machining
Stamping
Aircraft
Automotive
Thin Plastics
Variety of Applications

Please contact us for pricing and availability..!!

ZX-Series Data Logging Wall Thickness Gauge with USB Output

Total Measuring Range (depends on material and transducer/probe type)
0.025 – 36.000 inches
0.63 – 914.4 mm

Measuring Range on Steel (with standard T-102-2000 probe)
0.040 – 8.00 inches
1.00 – 199.9 mm

The  ZX-Series DL Wall Thickness Gauge accurately measures wall thickness and the extent of corrosion of all metals, ceramics, glass, and most rigid plastics – from only one side! It can measure thickness up to 36 inches (915 mm), depending upon the material and transducer.

Models Available

ZX-5DL
Data Logging Ultrasonic Wall Thickness Gauge Kit with T-102-2000 Probe Z-304-0001
ZX-6DL
Data Logging Thru-Paint Ultrasonic Thickness Gauge Kit with T-102-2700 Probe – Z-306-0001

Incorporates built-in data logging for 10,000 values with 250 readings per batch, up to 40 separate batches with USB Output. Data can be transferred into any program in “.csv” format or viewed in Datacomm Software (free download)

ZX- Series DL can be used in a Single Thickness Reading mode or in a Scan mode, where the probe is dragged over a large measuring area. The minimum thickness reading recorded during the “scan” will be displayed.

ZX-DL probe is waterproof and can be submerged in water. The gauge is impact-resistant and environmentally sealed (IP65) to provide trouble-free operation under the toughest field conditions.

Please contact us for pricing and availability..!!

TI-25DLXT

Measuring Range on Steel (with standard T-102-2700 probe)
Pulse-Echo (PE) Mode
(Pit & Flaw Detection) – 0.040 to 8.00 inches / 1.00 to 199.9mm
Echo-Echo (EE) Mode
(Through Paint & Coatings) – 0.100 to 1.000 inch / 2.54 to 25.40 mm

Total Measuring Range (Probe Dependant)
Pulse-Echo (PE) Mode
(Pit & Flaw Detection) – 0.025 to 36.000 inches / 0.63 to 914.4 mm
Echo-Echo (EE) Mode
(Through Paint & Coatings) – 0.100 to 1.000 inch / 2.54 to 25.40 mm

The new TI-25DLXT Wall Thickness Gauge accurately measures wall thickness and the extent of corrosion of all metals, ceramics, glass, and most rigid plastics from one side. When operated in E-E Mode (Thru-Paint Mode), the coating is eliminated from the reading and the gauge will display only the thickness of the metal wall.

The TI-25DLXT offers data logging for 10,000 values with 250 readings per batch, up to 40 separate batches, and USB Output. Data can be transferred into any program in CSV format or viewed in Datacomm Software (free download).

The TI-25DLXT’s probe is waterproof and can be submerged in water. The gauge is impact-resistant and environmentally sealed (IP65) to provide trouble-free operation under the toughest field conditions.

The TI-25DLXT can be used with any of the following hi-damped dual-element transducers specifically designed for use with E-E Thru-Paint Mode.

T-101-2700
3/16″ Diameter, 5.0 MHz Hi-damped transducer for thru paint measurement
T-101-3700
3/16″ Diameter, 7.5 MHz Hi-damped transducer for thru paint measurement
T-102-2700
1/4″ Diameter, 5.0 MHz Hi-Damped transducer for thru paint measurement – Standard Probe
T-102-3700
1/4″ Diameter, 7.5 MHz Hi-Damped Transducer for thru paint measurement
T-104-2700
1/2″ Diameter, 5.0 MHz Hi-Damped Transducer for thru paint measurement
T-104-9700
1/2″ diameter, 3.5 MHz Hi-Damped transducer for thru paint measurement

Please contact us for pricing and availability..!!

TI-25DLX

Total Measuring Range (depends on material and transducer/probe type)
0.025 – 36.000 inches
0.63 – 914.4 mm

Measuring Range on Steel (with standard T-102-3300 probe)
0.025 – 6.00 inches
0.60 – 150.0 mm

The TI-25DLX Wall Thickness Gauge accurately measures wall thickness and the extent of corrosion of all metals, ceramics, glass, and most rigid plastics – from only one side! It can measure thickness up to 36 inches (915 mm), depending upon the material and transducer.

Incorporates built-in data logging for 10,000 values with 250 readings per batch, up to 40 separate batches with USB Output. Data can be transferred into any program in “.csv” format or viewed in Datacomm Software (free download)

Complete Kit
The TI-25DLX is supplied as a complete kit with the gauge, probe, 4 oz. bottle of coupling fluid, 2 AA batteries, USB output cable, NIST-Traceable Calibration Certificate, and Operating Instruction Manual – all in a foam-fitted carrying case.

The TI-25DLX permits the operator to select from 8 preset materials as well as program 2 custom material velocities, plus allows free adjustment of the velocity as desired and allows the end-user to calibrate to a sample of known thickness where the velocity is automatically calculated. Additionally, to optimize linearity over a wide range, the user can perform a 2 point calibration to two samples of known thickness. The optimal velocity is automatically calculated to provide the highest accuracy and linearity between the low and high calibration points.

The TI-25DLX can be used in a Single Thickness Reading mode or in a Scan mode, where the probe is dragged over a large measuring area. The minimum thickness reading recorded during the “scan” will be displayed. The calibration and other setup parameters can be locked to prevent any accidental adjustments.

The TI-25DLX probe is waterproof and can be submerged in water. The gauge is impact-resistant and environmentally sealed (IP65) to provide trouble-free operation under the toughest field conditions.

Please contact us for pricing and availability..!!

MiniTest 400-Series

Robust and precise ultrasound thickness measurement gauge based on the ultrasonic pulse run-time method. Six ultrasonic test probes with frequencies ranging from 2 to 10 MHz in different designs to provide a broad spectrum of applications and thickness measurements ranging from 0.65mm to 500mm.

The high-temperature ultrasonic test probe enables the measurement of materials heated up to 350°C.

MiniTest 400: Ultrasonic thickness measuring gauge in 3 variants
MiniTest 420
Sturdy and economically priced basic model with memory, USB interface, and automatic probe-calibration detection. Standard and minimum measurement modes are available.
MiniTest 430
With integrated memory for 10 groups each with a maximum 500 measuring values and USB interface. Besides the MiniTest 420 model, the differential, alarm, and scanning measuring modes are also available.
MiniTest 440
The high-end device with integrated memory for 10 groups each with a maximum capacity of 500 measuring values, USB interface, and 5 measuring modes; connecting echo-echo probes is possible.

The device is equipped for automatic detection of the intelligent ultrasonic probes and re-calibration is not required upon switching probes. The calibration data of the sensor is saved in the probe.

Please contact us for pricing and availability..!!

TI-PVX

The new TI-PVX Precision Ultrasonic Wall thickness gauge provides the flexibility necessary for both high resolution and penetration requirements.

It’s the ability to use a variety of single element transducers for specific applications: Standard Delay Line (acrylic and graphite tips for metals and thin plastics), Pencil Delay Line (tough access area on thin materials), and Contact transducers (variety of applications) makes it the perfect flexible tool for very precise and delicate measurements. The adjustable resolution settings add to the PVX’s flexibility.

The selectable viewing options provide the user with additional flexibility during operation: (RF waveform, +/- Rectified waveform, and Large Digits with Scan Bar.

The time-based B-Scan feature displays a cross-section of the test material. Displays the profile of the opposite surface of the material.

The high-speed scan feature speeds up the inspection process by making 32 measurements per second. Remove the transducer from the test material and display the minimum measurement scanned.

Please contact us for pricing and availability..!!

TI-MVX

The model TI-MVX offers a series of advanced features including A-Scan, B-Scan as well as a complete alphanumeric data logging system with a storage capacity of thousands of data values and A-scan captures.

The TI-MVX features the highest resolution graphic LCD on the market and is specially engineered for optimal ease of use. It is supplied as a complete kit with all accessories in carrying case with FREE software, transfer cable, and NIST-Traceable Calibration Certificate.n.

Complete Kit
The TI-MVX is supplied as a complete kit with the gauge, 4 oz. bottle of coupling fluid, 2 AA batteries, NIST-Traceable Calibration Certificate, data transfer software, serial output cable, and Operating Instruction Manual – all in a foam-fitted carrying case.

Range in Steel
Pulse-Echo Mode
Pit and Flaw detection measures from 0.63 to 254 millimeters (0.025 – 9.999inches)
Echo-Echo Mode
Thru Paint & coatings measures from 2.54 to 102 mm (0.1 – 4.0 inches).
The range will vary +/- depending on the thickness of the coating.

Please contact us for pricing and availability..!!

TI-CMXDLP

Models Available
TI-CMXDLP
Black & white model
TI-CMXDLP-C
Color model

The new  TI-CMXDLP is the top-of-the-line model in the CMX Series of Gauges that measures both coating and wall thickness quickly and accurately—from only one side. In addition, when switched to Pulse-Echo mode, the TI-CMXDLP automatically measures and eliminates the coating from the wall thickness measurement, enabling the user to locate the finest corrosion and pitting—without removing the coating.

It features an A-Scan Display Mode allowing the user to see the actual waveform echoes, graphically, providing the insight necessary to tune the settings on the gauge for optimal performance. This is especially important for challenging measurement tasks.

The TI-CMXDLP also features a new E-EV Operating Mode (“Echo-Echo-Verify”), also known as Triple-Echo Mode, which provides added assurance that the displayed measurement is accurate and fully verified by subsequent echoes.

Measurement Modes
Pulse-Echo (corrosion mode)
Pulse-Echo Coating (Corrosion w/o coating)
Echo-Echo (thru-paint)
Temp Comp (auto-adjust for material temp)
Coating Only (Ultrasonic Coating Gauge)

Five user-selected operating modes are included
Coating On
Measures wall thickness using Pulse-Echo. It separately displays wall & coating thickness.
Coating Off
Measures wall thickness using Pulse-Echo. It displays wall thickness only.
Temperature Compensated
Measures wall thickness using Pulse-Echo and automatically adjusts calibration to compensate for changes in material temperature.
Thru-Coat
Measures wall thickness only using Echo-Echo. (coating is NOT included)
Coating Only Mode (CT)
(Coating Thickness) Measures from 0.0005 to 0.100 inches (0.013 to 2.540 mm). The range will vary slightly depending on the coating.

Please contact us for pricing and availability..!!

TI-CMXDL

The  TI-CMXDL accurately measures coating and wall thickness on a wide range of materials. Five selectable measuring modes enable the operator to precisely measure wall thickness, coating thickness, and locate corrosion and pitting—without removing the coating.

Oversized graphic LCD is backlit and features an easy to navigate menu allowing quick access to gauge settings and options.

Five user-selected operating modes are included
Coating On
Measures wall thickness using Pulse-Echo. It separately displays wall & coating thickness.
Coating Off
Measures wall thickness using Pulse-Echo. It displays wall thickness only.
Temperature Compensated
Measures wall thickness using Pulse-Echo and automatically adjusts calibration to compensate for changes in material temperature.
Thru-Coat
Measures wall thickness only using Echo-Echo. (coating is NOT included)
Coating Only Mode (CT)
(Coating Thickness) Measures from 0.0005 to 0.100 inches (0.013 to 2.540 mm). The range will vary slightly depending on the coating.

Measurement Modes
Pulse-Echo (corrosion mode)
Pulse-Echo Coating (Corrosion w/o coating)
Echo-Echo (thru-paint)
Temp Comp (auto-adjust for material temp)
Coating Only (Ultrasonic Coating Gauge)

Complete Kit
The TI-CMXDL is supplied as a complete kit with the gauge, probe, 4 oz. bottle of coupling fluid, 2 AA batteries, NIST-Traceable Calibration Certificate, operating manual, Software, RS-232 output cable, RS-232 to USB adapter, all in a foam-fitted carrying case.

Please contact us for pricing and availability..!!

TI-MMX-SDL

The new  TI-MMX-SDL is a full-featured ultrasonic thickness gauge offering an oversized display as well as a complete alphanumeric data logging system with a storage capacity of thousands of data values.

Complete Kit
The TI-MMX-SDL is supplied as a complete kit with the gauge, 4 oz. bottle of coupling fluid, 2 AA batteries, NIST-Traceable Calibration Certificate, data transfer software, serial output cable and Operating Instruction Manual – all in a foam-fitted carrying case.

The TI-MMX-SDL features the highest resolution graphic LCD on the market and is specially engineered for optimal ease of use.
TRANSDUCER SOLD SEPERATELY

Please contact us for pricing and availability..!!